Aluminum refinishing
Restore your aluminum fence instead of replacing it.
A factory-grade electrostatic repaint that bonds to the metal, eliminates chalking and oxidation, and adds years to a fence you already own — for a fraction of the cost of replacement.
What this is
Aluminum fence refinishing — what electrostatic recoating is.
Aluminum fence refinishing (electrostatic) is the on-site re-coating of an existing aluminum fence using the same atomized, electrically-charged powder-coat process the factory uses on new fence. The fence is grounded, the paint is charged with the opposite polarity, and the coating is pulled to the metal from every angle — front, back, the inside of every picket, and behind the rails — with negligible overspray. The result is a uniform, factory-grade architectural finish that bonds to the aluminum rather than sitting on top of it.
Allday Fence performs the refinish on residential and commercial aluminum perimeters across Miami-Dade County. Typical residential job: 1–2 days on site, fence stays in place, finish lasts 7–10 years in Miami sun and salt before the next recoat. Total cost is usually about a third of replacement — and we tell you honestly when replacement is the better call (out-of-plumb posts, fatigued welds, picket spacing that no longer meets pool code).
Why refinish
Most aluminum fences don't need replacing — they need recoating.
Aluminum fences age in a specific way. The metal itself stays sound — it doesn't rot, rust through, or rust-stain the concrete. What fails is the factory coating: chalking, fading, hairline chipping, and that dusty look powder-coat takes on after a decade in Florida sun.
Electrostatic refinishing is the answer. We charge the fence, atomize the coating, and the paint wraps the entire profile — front, back, and every picket edge — bonded to the metal with almost no overspray. You get a factory-quality finish without taking the fence down.
Quick math
How it works
A four-step refinish, done on the property.
Inspect & prep
We walk the fence and identify oxidation, loose existing coating, and any sections needing minor repair. Surfaces are scuffed, degreased, and cleaned of chalking before any paint moves.
Electrostatic application
The fence is grounded and the paint is electrically charged. The atomized coating is pulled to the metal from every angle — front, back, and the inside of every picket — with negligible overspray.
Cure & inspect
The coating cures quickly. We inspect coverage from both sides, touch up any thin spots, and document the work so it's clear what was done.
Site cleanup
Drop cloths, masking, and all materials packed out the same day. Your landscaping, hardscape, and pool deck are protected the entire time we're on site.
Why electrostatic vs. a brush-and-roller repaint
The same physics the factory uses to coat your fence the first time.
Wraps the full profile.
Charged paint is pulled around every edge — front, back, top rail, picket caps. A brush only reaches what you can see; electrostatic reaches everything.
Bonds to the metal.
The charge attaches the coating directly to the aluminum. The result resists chipping, peeling, and the chalking that finishes most brush jobs.
Almost no overspray.
The paint wants to land on the fence, not the lawn. A typical residential project goes from start to clean-up inside two days.
When refinishing is the right call
And when we'll tell you to replace instead.
The fence is structurally sound.
Posts are plumb, rails are tight, hardware works. The fence just looks tired — chalky, faded, scuffed, scratched from a contractor's truck. Refinishing is almost always cheaper than replacement and the result reads as a new fence.
The fence has structural failure.
Posts are out of plumb. Rails are bent. Hurricane load has fatigued welds. Pool-code spacing is non-compliant. In those cases we'll quote replacement honestly — we'd rather not put a fresh finish on a fence we know is going to fail.
Colors & finishes
Match what's there, or change it entirely.
Standard architectural colors — bronze, black, white, sandstone, beige — plus custom matches against an existing trim color, HOA palette, or product chart. Satin and matte finishes both available.
Common questions
What people ask before they call.
What is electrostatic fence refinishing?
It's the same atomization process the factory uses to coat your fence the first time. We ground the fence, electrically charge the paint, and the coating is pulled to the metal from every angle — front, back, and the inside of every picket — with negligible overspray.
How much does aluminum fence refinishing cost vs. replacement?
Refinishing typically runs about a third of the cost of a full aluminum fence replacement. Exact pricing depends on linear footage, color, and the condition of the existing coating, but the savings vs. replacement are usually substantial.
How long does the refinish take and how long does it last?
Most residential perimeters are done in 1–2 days on site with no fence removed. A properly prepped electrostatic finish typically lasts 7–10 years in South Florida sun before the next recoat.
When should I replace the fence instead of refinishing?
Refinish when the fence is structurally sound — posts plumb, rails tight, hardware working — and just looks tired. Replace when posts are out of plumb, rails are bent, welds are fatigued, or the picket spacing doesn't meet pool code. We'll tell you honestly which is right for your fence.
What colors can I refinish my fence in?
Standard architectural colors — bronze, matte black, white, sandstone, beige — plus custom matches against an existing trim color, HOA palette, or product chart. Satin and matte finishes both available.
Does refinishing require a permit in Miami-Dade?
No. On-site refinishing of an existing aluminum fence is maintenance — no permit is required because the structure isn't changing. We do confirm the original fence was permitted (a quick MyHausFax™ property-record check), so if there's an open or missing permit hiding in the history, we surface it before we coat over the issue.